How many pounds of flakes for a 3 car garage?
About 106 pounds of 1/4 in flakes for a full broadcast on a 32 × 24 ft three-car garage (768 square feet), including 10% extra — 3 boxes of 40 lb.
How to work it out
- 32 ft × 24 ft = 768 sq ft
- 768 sq ft × 0.125 lb/sq ft = 96 lb; + 10% = 106 lb
- 106 lb ÷ 40 lb per box = 2.64 → 3 boxes
Three-car garages commonly run about 30–36 ft wide and 22–26 ft deep; 32 × 24 ft is a typical middle, the same size the 3-car garage epoxy kit example uses. At 768 sq ft the chips are a real purchase — over a hundred pounds for a full broadcast.
Adjust for your project
More options: waste · $/box
- Boxes of chips
- 3 boxes
- Floor area
- 768 sq ft
- Broadcast rate used
- 0.125 lb per sq ft (about 8 sq ft per lb)
- Flakes before the allowance
- 96 lb
- One box covers (before the allowance)
- 320 sq ft
- Spare chips in the last box
- 14.4 lb
- A full broadcast leaves loose chips on top once the coat cures. They’re scraped and swept off — keep the clean ones for touch-ups — and most flake floors then get a clear topcoat.
Flakes for a 32 × 24 ft garage by broadcast and chip size
| Broadcast | Flakes to buy (by weight) | Boxes of chips | Spare chips in the last box |
|---|---|---|---|
| Partial broadcast | 16.9 lb | 1 box | 23.1 lb |
| Full broadcast, 1/4 in chips | 106 lb | 3 boxes | 14.4 lb |
| Full broadcast, 1/8 in or hybrid | 169 lb | 5 boxes | 31 lb |
What to know about flaking a three-car garage
Three 40 lb boxes hold 120 lb against about 106 lb needed, leaving roughly 14 lb — a little over 10% spare on a floor this big. That’s enough for uneven throwing near the walls, but not for a change of mind about chip size: 1/8 in chips or a hybrid blend at 0.20 lb per sq ft push the floor to about 169 lb, or five boxes.
Order every box in one blend and one order. On a 768 sq ft floor the chips from different boxes end up side by side across the whole width, and blends can shift between production runs. Open all the boxes and mix them together in a clean bin before you start, so any variation spreads evenly rather than showing as a stripe.
Three bays is too much floor to broadcast in one pass. Split it at the control joints — usually one bay at a time — and mix only as much base coat as one section takes, so the chips always land in a wet coat. The floor coating calculator shows the area one kit of base coat covers, which sets the size of each section.
If you’re thinking about a lighter, partial broadcast to save on chips, it changes the topcoat as well: WALT Tools calls for two topcoats over a partial broadcast instead of one. The flakes per square foot chart compares the partial and full rates side by side. For the boxed kits on the same floor, see How much epoxy for a 3-car garage floor; for a smaller floor, how many pounds of flakes for a 2 car garage.
Different size? Use the full Epoxy Flake Calculator.
What you’ll need
- Decorative floor flakesMid-range price
Broadcast into the wet base coat for texture and to hide imperfections. Coverage depends on chip size.
See options on Amazon (opens in a new tab) - Spiked shoesBudget price
Strap-on spikes let you walk across a wet coat to broadcast flakes or back-roll without leaving footprints.
See options on Amazon (opens in a new tab) - Floor epoxy coating (by the gallon)Premium price
Two-part floor coating sold by volume rather than as a boxed garage kit. The data sheet gives film thickness and coverage.
See options on Amazon (opens in a new tab)
As an Amazon Associate we earn from qualifying purchases. Links to products are affiliate links — they cost you nothing extra and help keep these calculators free.
Frequently asked questions
How many pounds of 1/8 inch flakes for a 3 car garage?
About 169 pounds on a 32 × 24 ft floor at 0.20 lb per square foot with 10% extra — 5 boxes of 40 lb.
How many 25 lb boxes of flakes for a 3 car garage?
5 boxes of 25 lb for a full broadcast of 1/4 in chips: the floor needs 106 pounds with 10% extra.
How many pounds of flakes for a 36 × 24 three-car garage?
About 119 pounds of 1/4 in chips for a full broadcast on 864 square feet — 3 boxes of 40 lb.
Sources
- Concrete Floor Supply — Epoxy flake calculator (opens in a new tab) — Full coverage: about 0.10 lb/sq ft (10 lb per 100 sq ft) for 1/4 in flakes and 0.20 lb/sq ft for 1/8 in or hybrid blends; figures are minimums, order 10–15% extra.
- WALT Tools — Flake flooring (opens in a new tab) — Chips planned at about 8 sq ft per lb for a full broadcast; real use about 5–10 sq ft per lb depending on chip size and technique. A partial broadcast uses less and calls for two topcoats.
- OneStopEpoxy — 1/4 in vinyl flakes (opens in a new tab) — Full broadcast: 1 lb of flakes for every 8 sq ft. Partial broadcast: 5–10 lb for every 400 sq ft, depending on the look.
- Legacy Industrial — ColorFlake decorative chips (opens in a new tab) — Partial broadcast about 1 lb per 150 sq ft; full broadcast about 90 lb per 500 sq ft. Sold in 10, 20, 30 and 40 lb quantities.