Epoxy flake calculator: how many pounds of flakes?
Enter your floor size and how heavily you’ll throw the chips to get the pounds of flakes and the boxes to buy. A full broadcast of 1/4 in flakes takes about 1 lb per 8 sq ft.
Enter your measurements
More options: waste · $/box
- Boxes of chips
- 2 boxes
- Floor area
- 400 sq ft
- Broadcast rate used
- 0.125 lb per sq ft (about 8 sq ft per lb)
- Flakes before the allowance
- 50 lb
- One box covers (before the allowance)
- 320 sq ft
- Spare chips in the last box
- 25 lb
20 ft × 20 ft = 400 sq ft
400 sq ft × 0.125 lb/sq ft = 50 lb; + 10% = 55 lb
55 lb ÷ 40 lb per box = 1.38 → 2 boxes
- A full broadcast leaves loose chips on top once the coat cures. They’re scraped and swept off — keep the clean ones for touch-ups — and most flake floors then get a clear topcoat.
Flakes needed by broadcast and chip size (at the floor size above)
| Broadcast | Flakes to buy (by weight) | Boxes of chips |
|---|---|---|
| Partial broadcast | 8.8 lb | 1 box |
| Full broadcast, 1/4 in chips | 55 lb | 2 boxes |
| Full broadcast, 1/8 in or hybrid | 88 lb | 3 boxes |
Decorative flakes (also called chips or vinyl chips) are thrown by hand into a wet epoxy or polyaspartic base coat. They’re sold by weight, so the question is always “how many pounds?” — and the answer depends on two things: whether you cover the floor completely, and how big the chips are.
How the pounds are worked out
Multiply the floor area by a broadcast rate in pounds per square foot, add an allowance for uneven throwing, and round up to whole boxes. A 20 × 20 ft floor is 400 sq ft; at 0.125 lb per sq ft a full broadcast is 50 lb, or 55 lb with 10% extra — two 40 lb boxes.
area = length × width flakes = area × broadcast rate × (1 + allowance) boxes = flakes ÷ box size (round up) 1 lb per 8 sq ft = 0.125 lb per sq ft = about 0.61 kg/m²
Published flake coverage rates
| Broadcast and chip | Published rate | Per 100 sq ft |
|---|---|---|
| Full, 1/4 in chips | 0.10 lb/sq ft (Concrete Floor Supply, a minimum); 1 lb per 8 sq ft (WALT Tools, OneStopEpoxy) | 10–12.5 lb |
| Full, 1/8 in chips or hybrid blend | 0.20 lb/sq ft (Concrete Floor Supply) | 20 lb |
| Full, any chip (real-world range) | 5–10 sq ft per lb (WALT Tools); about 90 lb per 500 sq ft (Legacy Industrial) | 10–20 lb |
| Partial broadcast | 5–10 lb per 400 sq ft (OneStopEpoxy); about 1 lb per 150 sq ft (Legacy Industrial) | about 0.7–2.5 lb |
The calculator uses 0.125 lb per sq ft for a full broadcast of 1/4 in chips, 0.20 for 1/8 in chips and hybrid blends (mixes of large and small chips), and 2 lb per 100 sq ft for a partial broadcast. Pick My supplier’s rate to type your own. The pounds of flakes per square foot page lays the same figures out per 100 and per 1,000 sq ft.
Full broadcast vs partial broadcast
- Full broadcast (“to rejection”): you keep throwing until the wet coat can’t hold any more chips and no base color shows. It hides imperfections in the slab, gives the most texture and uses several times the chips of a partial broadcast. It’s the usual garage and showroom flake floor.
- Partial broadcast: you stop early so the colored base coat shows between the chips. It uses a few pounds per hundred square feet, but WALT Tools notes it calls for two topcoats rather than one, because the smoother base and the chip edges both need covering.
- Chip size: at full coverage, small chips take more weight than large ones — Concrete Floor Supply plans twice the pounds for 1/8 in chips as for 1/4 in.
Common garage sizes
Worked examples: how many pounds of flakes for a 2 car garage (20 × 20 ft, with 24 × 24 ft as a variant) and how many pounds of flakes for a 3 car garage (32 × 24 ft). For the coating itself, the garage floor epoxy calculator counts boxed kits, and the floor coating calculator works out the base coat and clear topcoat by the gallon — including the extra topcoat a rough, chip-covered surface takes.
Tips for buying and throwing flakes
- Buy the whole job in one blend from one order. Blends vary between batches, and a second order can show as a line across the floor.
- Throw upward so the chips fall like snow; tossing them down puts them in clumps.
- Broadcast while the base coat is wet, section by section — one person rolls, another follows with the chips. Spiked shoes let you walk on the wet coat.
- Concrete Floor Supply calls its rates minimums and suggests ordering 10–15% extra. Leftover clean chips are handy for touch-ups.
- Once the base has cured, scrape and sweep off the loose chips before the topcoat. Pricing the whole job for a client? The floor job bid calculator adds labor and markup.
What you’ll need
- Decorative floor flakesMid-range price
Broadcast into the wet base coat for texture and to hide imperfections. Coverage depends on chip size.
See options on Amazon (opens in a new tab) - Spiked shoesBudget price
Strap-on spikes let you walk across a wet coat to broadcast flakes or back-roll without leaving footprints.
See options on Amazon (opens in a new tab) - Floor epoxy coating (by the gallon)Premium price
Two-part floor coating sold by volume rather than as a boxed garage kit. The data sheet gives film thickness and coverage.
See options on Amazon (opens in a new tab) - Epoxy roller kit (3/8 in nap)Budget price
Shed-resistant roller covers, frame and tray. Have spare covers — a roller that starts to gel is done.
See options on Amazon (opens in a new tab)
As an Amazon Associate we earn from qualifying purchases. Links to products are affiliate links — they cost you nothing extra and help keep these calculators free.
Frequently asked questions
How many square feet does a 40 lb box of flakes cover?
About 320 sq ft for a full broadcast of 1/4 in chips at 1 lb per 8 sq ft, or about 200 sq ft with 1/8 in chips at 0.20 lb per sq ft — before any allowance. As a partial broadcast, a 40 lb box goes much further: at 2 lb per 100 sq ft it would cover about 2,000 sq ft.
Do smaller flakes take more pounds per square foot?
Yes, for a full broadcast. Concrete Floor Supply plans about 0.10 lb per sq ft for 1/4 in flakes and 0.20 lb for 1/8 in flakes and hybrid blends — twice the weight, because small chips pack more tightly to cover the same floor.
How many pounds of flakes for a 2 car garage?
About 55 lb for a full broadcast of 1/4 in chips on a 20 × 20 ft garage, including 10% extra — two 40 lb boxes. See how many pounds of flakes for a 2 car garage for bigger two-car floors and smaller chips.
What is the difference between a full and a partial flake broadcast?
A full broadcast covers the base coat completely — you throw until it won’t take any more chips. A partial broadcast leaves the base color showing between the chips and uses only a few pounds per hundred square feet. See the flakes per square foot chart for both.
Do I need a topcoat over epoxy flakes?
Most flake systems get a clear topcoat once the loose chips are scraped off, to lock them in and make the floor easier to clean. WALT Tools specifies one topcoat over a full broadcast and two over a partial one. The rough surface takes more topcoat than a smooth floor — the floor coating calculator allows for that.
Related guides
Sources
- Concrete Floor Supply — Epoxy flake calculator (opens in a new tab) — Full coverage: about 0.10 lb/sq ft (10 lb per 100 sq ft) for 1/4 in flakes and 0.20 lb/sq ft for 1/8 in or hybrid blends; figures are minimums, order 10–15% extra.
- WALT Tools — Flake flooring (opens in a new tab) — Chips planned at about 8 sq ft per lb for a full broadcast; real use about 5–10 sq ft per lb depending on chip size and technique. A partial broadcast uses less and calls for two topcoats.
- OneStopEpoxy — 1/4 in vinyl flakes (opens in a new tab) — Full broadcast: 1 lb of flakes for every 8 sq ft. Partial broadcast: 5–10 lb for every 400 sq ft, depending on the look.
- Legacy Industrial — ColorFlake decorative chips (opens in a new tab) — Partial broadcast about 1 lb per 150 sq ft; full broadcast about 90 lb per 500 sq ft. Sold in 10, 20, 30 and 40 lb quantities.