How many pounds of flakes for a 2 car garage?
About 55 pounds of 1/4 in flakes for a full broadcast on a 20 × 20 ft two-car garage (400 square feet), including 10% extra — 2 boxes of 40 lb.
How to work it out
- 20 ft × 20 ft = 400 sq ft
- 400 sq ft × 0.125 lb/sq ft = 50 lb; + 10% = 55 lb
- 55 lb ÷ 40 lb per box = 1.38 → 2 boxes
Twenty by twenty feet is the standard two-car garage, and 1/4 in chips are the size most garage flake floors use. The figure here is for a full broadcast — chips thrown until no base color shows — at 1 lb per 8 sq ft, the planning rate WALT Tools and OneStopEpoxy both publish.
Adjust for your project
More options: waste · $/box
- Boxes of chips
- 2 boxes
- Floor area
- 400 sq ft
- Broadcast rate used
- 0.125 lb per sq ft (about 8 sq ft per lb)
- Flakes before the allowance
- 50 lb
- One box covers (before the allowance)
- 320 sq ft
- Spare chips in the last box
- 25 lb
- A full broadcast leaves loose chips on top once the coat cures. They’re scraped and swept off — keep the clean ones for touch-ups — and most flake floors then get a clear topcoat.
Flakes for a 20 × 20 ft garage by broadcast and chip size
| Broadcast | Flakes to buy (by weight) | Boxes of chips | Spare chips in the last box |
|---|---|---|---|
| Partial broadcast | 8.8 lb | 1 box | 31.2 lb |
| Full broadcast, 1/4 in chips | 55 lb | 2 boxes | 25 lb |
| Full broadcast, 1/8 in or hybrid | 88 lb | 3 boxes | 32 lb |
What to know about flaking a two-car garage
Two 40 lb boxes hold 80 lb against the 55 lb needed, so about 25 lb is left — a comfortable margin for a first floor, and enough for touch-ups later. Concrete Floor Supply’s lighter minimum of 0.10 lb per sq ft would put the same floor at 40 lb before any extra, which is why its calculator pairs the rate with advice to order 10–15% more. Either way it’s two boxes; the difference shows up when the chips are smaller.
Switch to 1/8 in chips or a hybrid blend and the weight jumps: at 0.20 lb per sq ft the garage takes about 88 lb with the allowance, which is three 40 lb boxes. Small chips give a finer, more granite-like look but cover less per pound.
“Two-car” isn’t one size. A roomier 24 × 24 ft garage is 576 sq ft, and at the 1/4 in rate it needs about 79 lb — two boxes again, but with less than a pound to spare, so most installers would buy a third. Measure the floor rather than counting doors. The pounds of flakes per square foot chart scales the rates to any size.
On a 400 sq ft floor the broadcast has to keep pace with the roller: chips only stick to a wet coat. Work in sections along the saw-cut control joints, with one person rolling and another throwing, and wear spiked shoes to walk on the wet coat. For the kits under the chips, see How much epoxy for a 20×20 two-car garage; for three bays, how many pounds of flakes for a 3 car garage.
Different size? Use the full Epoxy Flake Calculator.
What you’ll need
- Decorative floor flakesMid-range price
Broadcast into the wet base coat for texture and to hide imperfections. Coverage depends on chip size.
See options on Amazon (opens in a new tab) - Spiked shoesBudget price
Strap-on spikes let you walk across a wet coat to broadcast flakes or back-roll without leaving footprints.
See options on Amazon (opens in a new tab) - Garage floor epoxy kitPremium price
Boxed kits usually include the base coat and sometimes etch and flakes. Check coverage per coat and what’s actually in the box.
See options on Amazon (opens in a new tab)
As an Amazon Associate we earn from qualifying purchases. Links to products are affiliate links — they cost you nothing extra and help keep these calculators free.
Frequently asked questions
How many pounds of 1/8 inch flakes for a 20 × 20 garage?
About 88 pounds at 0.20 lb per square foot with 10% extra — 3 boxes of 40 lb.
How many pounds of flakes for a 24 × 24 garage?
About 79.2 pounds of 1/4 in chips for a full broadcast on 576 square feet — 2 boxes of 40 lb, with only 0.8 pounds to spare.
How many pounds of flakes for a partial broadcast in a 2 car garage?
About 8.8 pounds on a 20 × 20 ft floor at 2 lb per 100 square feet with 10% extra — 1 box of 40 lb is far more than enough, so buy a smaller bag.
Sources
- Concrete Floor Supply — Epoxy flake calculator (opens in a new tab) — Full coverage: about 0.10 lb/sq ft (10 lb per 100 sq ft) for 1/4 in flakes and 0.20 lb/sq ft for 1/8 in or hybrid blends; figures are minimums, order 10–15% extra.
- WALT Tools — Flake flooring (opens in a new tab) — Chips planned at about 8 sq ft per lb for a full broadcast; real use about 5–10 sq ft per lb depending on chip size and technique. A partial broadcast uses less and calls for two topcoats.
- OneStopEpoxy — 1/4 in vinyl flakes (opens in a new tab) — Full broadcast: 1 lb of flakes for every 8 sq ft. Partial broadcast: 5–10 lb for every 400 sq ft, depending on the look.
- Legacy Industrial — ColorFlake decorative chips (opens in a new tab) — Partial broadcast about 1 lb per 150 sq ft; full broadcast about 90 lb per 500 sq ft. Sold in 10, 20, 30 and 40 lb quantities.