How much metallic epoxy for a 2-car garage floor?

Short answer

You need about 8.78 gallons of metallic epoxy for a 32-mil metallic coat on a 20 × 20 ft two-car garage (400 square feet), including 10% extra — 3 kits of 3 gallons, with only 0.22 gallons to spare.

How to work it out

  1. 20 ft × 20 ft = 400 sq ft
  2. 1,604 ÷ 32 mils = 50.1 sq ft/gal
  3. 400 sq ft ÷ 50.1 sq ft/gal × 1.1 = 8.78 gal per coat × 1 = 8.78 gal
  4. 8.78 gal ÷ 3 gal per kit = 2.93 → 3 kits
  5. Area per batch = 3 gal ÷ 1.1 × 50.1 sq ft/gal = 137 sq ft of metallic coat

Metallic coats are poured roughly three times as thick as a standard 10-mil floor coat, so the gallons climb fast. This example uses 32 mils — the film behind the 50 sq ft per gallon that BDR Coatings’ EP-1000 data sheet and OneStopEpoxy’s Metallic Dream page both give — on a 400 sq ft two-car garage, and 10% extra rather than the usual 15% because the metallic goes over a sealed base coat, not bare concrete.

Adjust for your project

ft
ft
Metallic epoxy goes on far thicker than a standard coat — data sheets commonly give 30–40 mils (750–1,000 µm) in a single coat. Enter yours under Film thickness and set the coats to 1.
mils
From the data sheet (1 mil = 1/1,000 in). Thin water-based coats are around 4 mils, 100%-solids coats often 8–20.
Coats of this product. A clear topcoat of a different product goes in Topcoat below.
%
On the data sheet as “volume solids” or “solids by volume”. 100%-solids epoxy is 100; water-based coatings are much lower.
mils
A clear coat of a different product over the base — e.g. to lock in flakes. Same basis (wet or dry) as above. Leave blank for none.
sq ft/gal
Leave blank for no primer. From the primer’s data sheet — ground concrete: typically 200–300 sq ft/gal.
gal
Mixed size of one kit or pail — both parts together.
More options: waste 10%
ft
Cove base = the coating carried up the wall as a curved skirting. Enter the length of wall it runs along; leave blank for none.
%
Porous concrete, roller and tray losses
gal
Mixed coating per batch. Leave blank to mix one whole kit at a time — the usual way on floors.
$
Optional — your kit price, for a cost estimate (the same price is used for every product).
Floor coating to buy (all coats)8.78 gal35.1 qt · 33.2 L
Kits to buy
3 kits
Per base coat
8.78 gal (35.1 qt · 33.2 L)
Floor area
400 sq ft
Theoretical coverage per base coat
50.1 sq ft/gal
Wet film per base coat
32 mils
Approx. dry film per base coat
32 mils
Batches per base coat
3 batches
Area one batch covers
1 × 3 gal kit ≈ 137 sq ft at 32 mils — chalk-line the floor into sections this size
Left over in part-used kits
0.22 gal (0.89 qt · 0.84 L)
  • What to buy: 3 × 3 gal kits of floor coating. Each kit has both parts (resin + hardener) — you don’t buy them separately. Looking at a different kit size? Change Size of the kit you’re buying above.
  • Tight fit: only 0.22 gal spare. Thirsty or freshly ground concrete can use that up in the first coat — consider one more kit.
  • Metallic pigment: BDR Coatings’ EP-1000 data sheet calls for 4–8 oz per 3-gallon kit — about 12–23 oz for this metallic coat. Use your pigment maker’s figure if it differs.
  • A metallic coat goes over a solid-color base coat and usually gets a clear topcoat. Work out the base coat as a separate item (Film thickness, at its own mils) and add the topcoat under Topcoat thickness.

For this job · affiliate link
Floor epoxy coating (by the gallon)Plan on 8.78 gal — 3 × 3 gal kits. Check that the data sheet’s coverage at 32 mils wet matches — that’s the number the gallons hang on.
View on Amazon (opens in a new tab)

Metallic epoxy for a 20 × 20 ft garage by film thickness (3 gal kits)

Metallic epoxy for a 20 × 20 ft garage by film thickness (3 gal kits)
Metallic filmTheoretical coverage per base coatFloor coating to buy (all coats)Kits to buy
30 mils53.5 sq ft/gal8.23 gal3 kits
32 mils50.1 sq ft/gal8.78 gal3 kits
36 mils44.6 sq ft/gal9.87 gal4 kits
40 mils40.1 sq ft/gal11 gal4 kits

What to know about a metallic garage floor

Three 3-gallon kits hold 9 gallons against about 8.78 needed, which leaves less than a quart. That is tight for a pour you can’t pause: a metallic coat has to be finished wet-into-wet, and running out two feet from the door leaves a seam you can’t hide. At OneStopEpoxy’s 50 sq ft per gallon a 3-gallon kit covers about 150 sq ft, so 400 sq ft is about 2.7 kits before any extra — most installers would buy a fourth and keep the spare for a test board.

The metallic coat is only one of three layers. Under it goes a solid-color base coat, usually a standard pigmented epoxy at its own, much thinner film — work it out separately with the calculator above at that film, for example 400 sq ft at 10 mils. Over it goes a clear topcoat: EP-1000’s data sheet lists clear coats at 5–8 mils (200–300 sq ft per gallon) and 8–12 mils (133–200 sq ft per gallon).

Pigment is measured per kit. EP-1000 calls for 4–8 oz of metallic pigment per 3-gallon kit, mixed into the resin side and left to wet out before the hardener goes in — so this floor takes roughly 12–23 oz of one color, bought in one order. Thicker pours of 36–40 mils give more depth to the swirl but push the floor to four kits, as the table shows.

Garage slabs take every coat from below as well as above: check the slab temperature and the dew point before you pour, since EP-1000’s data sheet wants the slab at least 3°C (5.5°F) above the dew point. The cure time calculator adjusts the label times for a cold garage.

What you’ll need

As an Amazon Associate we earn from qualifying purchases. Links to products are affiliate links — they cost you nothing extra and help keep these calculators free.

Frequently asked questions

How much metallic epoxy for a 24 × 24 garage floor?

About 12.6 gallons at 32 mils with 10% extra on 576 square feet — 5 kits of 3 gallons.

How much metallic epoxy for a 2-car garage at 40 mils?

About 11 gallons: at 40 mils a gallon covers only 40.1 square feet per gallon, so the 400 sq ft floor takes 4 kits of 3 gallons.

How much clear topcoat over a metallic garage floor?

About 2.19 gallons for an 8-mil clear topcoat on 400 square feet with 10% extra, on top of the 8.78 gallons of metallic coat.

Sources